Overview
This Holybro SiK 1W Telemetry Radio is a small, light, and inexpensive open-source radio platform with a maximum 50 kilometres range (outdoors, line-of-sight range).
This radio is plug-and-play, ready for all Pixhawk Standard and other similar flight controllers, providing the easiest way to set up a telemetry connection between your controller and a ground station. It uses open-source firmware that has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Ardupilot, QGroundControl, and PX4.
The radios are available in 915 MHz or 433 MHz versions. Please purchase the model that is appropriate for your country/region.
Features
- Open-source SIK firmware
- Plug-n-play for Pixhawk Standard Flight Controllers
- 1W maximum RF output
- The Easiest way to connect your controller and Ground Station
- Interchangeable air and ground radio
- 6-position JST-GH connector
Specifications
SiK Telemetry Radio 100mW | SiK Telemetry Radio 500mW | SiK Telemetry Radio 1W | |
---|---|---|---|
Max RF Power | 20 dBm | 27 dBm | 30 dBm |
Receive sensitivity | -121 dbm @2kbps RF Data Rate, -105 dbm @64kbps RF Data Rate | ||
Antenna Gain | 2dBi | 5dBi | |
RF Data Rates | 2, 4, 8, 16, 32, 64(default), 96, 128, 192, 250 kbps | ||
Serial Interface Data Rate | 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6(default), 115.2 kbps | ||
Frequency Band | 902MHz - 928MHz or 414MHz - 460MHz | ||
Interference Immunity | Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle | ||
Address Options | Network ID: 0 –255 | ||
Channels | Up to 50 Frequency Hopping Channels | ||
Supported Network Topologies | Point-to-point | ||
Configuration Method | MissionPlanner or AT Commands | ||
Data Framing | Standard or MAVLink protocol framing | ||
Error correction | Corrects up to 25% of bit errors with open-source SIK firmware | ||
Serial Data Connector & Interface | 6-pin JST-GH connector, 3.3V-TTL | ||
USB | Micro-USB | Type-C | |
SMA Connector | RP-SMA female | ||
Power Connector | NA | XT30 | |
Operating Temperature | -40~85°C | ||
Dimension | 28 x 53 x 10.7mm (without antenna) | 66.5 x 32 x 16.5mm (without antenna) | |
Weight | 23.5g w/ antenna | 67g w/ antenna | |
Input Voltage (DC) | 5V | 7~28V |
- 2-way full-duplex communication through adaptive TDM UART interface
- Transparent serial link
- MAVLink protocol framing
- Built in FT230X/FT231 USB to BASIC UART conversion IC
Electrical Data
- Supply voltage: 7~28V DC via XT30
- Transmit current: 12V/400mA at 30 dBm
- Receive current: 12V/30mA
- Serial interface: 3.3 V UART
Package Included
-
Single 1W
- 1W Radio modules with antennas *1
- High-gain omnidirectional antenna *1
- Male Type-C to male Type-C USB cable *1
- Male XT30 to female XT30 adapter cable *1
- Male XT30 to female XT60 adapter cable *1
- JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
-
Rubber damping grommet *3
-
Pair 1W
- 1W Radio modules with antennas *2
- High-gain omnidirectional antenna *2
- Male Type-C to male Type-C USB cable *1
- Male XT30 to female XT30 adapter cable *1
- Male XT30 to female XT60 adapter cable *1
- JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
-
Rubber damping grommet *3
Manual:
Telemetry-Radio-V3-Quick-Start-Guide
Some Tips:
https://ardupilot.org/copter/docs/common-configuring-a-telemetry-radio-using-mission-planner.html
You may also like
